Wikia

Solar Cookers World Network

WAPI production

Talk0
1,856pages on
this wiki
Revision as of 17:57, November 4, 2013 by Tom Sponheim (Talk | contribs)


Below is detailed information about buying and/or making Water Pasteurization Indicators (WAPIs).

Purchasing WAPIs from Solar Cookers International

WAPIs can be purchased from Solar Cookers International (SCI). For information on bulk purchases, contact the office at +1 (916) 455-4499.

Superwapi1 large

The WAPI model sold by Solar Cookers International

Making your own

  1. If you make them yourself you run into quality control issues. Here is how Bob Metcalf handles quality control on the ones he makes. After he makes them, he puts them into hot water so that the wax melts and runs into the bottom of the tube. Then he inspects them visually for any holes in the tube and for the other indicator of a problem: water inside the tube. Then he repeats the process a second time. You can melt the wax of a batch of WAPIs at one time, rather than heating one individually. When heating them in water, watch for wax coming to the surface of the hot water. That will be a sign that one or more of the WAPIs in that batch definitely are leaking. Whether or not you see wax on the surface of the water, each and every WAPI should be visually inspected after both of the hot water tests. Any WAPI that shows any sign of leakage is thrown away in a place where it will be sure not to get mixed up with the good WAPIs. Bob says he throws away 1 out of every 10 or 15 WAPIs he makes, so you can see that there is a cost factor to consider.
  2. Making one or two WAPIs is a major pain. The tubing comes in 8-foot lengths, which makes it a little hard to handle. Bob uses a band saw available at his university to cut them, but he describes the cutting process as a "bother."
  3. In addition to purchasing the wax and the tubing, you'll also have to purchase the fish line and the washers.
Rotary Youth Leadership Awards youth Southern CA 2009

Rotary Youth Leadership Awards youth making WAPIs in Southern California for use in projects around the world.

Bob Metcalf is willing to give you a small supply of the wax, which he estimates will be more than enough for 500 WAPIs and perhaps enough for 1000.

The wax for use inside the WAPI is available here:

Quest International
5115 Sedge Blvd.
Hoffman Estates, IL 60192
USA

Tel: +1 (847) 645-7000
F: +1 (847) 645-7064

The type of wax we use is called Myverol, and the specific product is known as Myverol 18-06, which has a melting point of 69° C. Apparently, the smallest unit that they sell this product in is a box about 1 foot square, which weighs about 45 pounds (20 kg). Bob Metcalf has not yet used up one box and I'm not sure he even expects to in his lifetime--it would be enough for untold thousands of WAPIs.

The tubing we use is .373 inches outside diameter, and the wall thickness is about .060 inches. It is important to be sure that you use a polycarbonate tubing, which Lexan is, but double check with your dealer, because other plastics (ones that are not polycarbonate) lack either the temperature stability or the optical clarity that is needed.

The Lexan tubing can be obtained from McMaster-Carr in Los Angeles. This is the contact info:

McMaster-Carr Supply Co.
P.O. Box 54960
Los Angeles, CA 90054-0960
USA

Phone: 562-692-5911
F: 562-695-2323

http://www.mcmaster.com

The product number is 8585K11. It comes only in 8 ft. lengths. at 60 cents a foot. The measurements I gave you above were more exact than what the company's website gives--it says 3/8 inch exterior diameter and 1/4 inch interior diameter, which is pretty darn close to the figures I gave you above.

I have been instructed by the higher authorities to once again stress with you the idea of quality control--checking every WAPI twice, and looking to see if ANY water has gotten inside the WAPI, because water will affect the wax, which will then possibly melt at temperatures below pasteurization temperature.

Bob Metcalf says, that when you make the WAPI's you put enough wax in the tube to fill it about half way. (The wax comes dry and powdered, looking a lot like fine grated Parmesan cheese.) After the first time it melts, it will be a solid chunk at the bottom of the tube.

Bob Nepper also has worked with Rotary Clubs to build large numbers of WAPIs for use in international projects.

WAPIs with stainless steel wire

The Monterey Peninsula Rotary Club now has WAPI kits available in which stainless steel wire replaces the monofiliment fishing line and is good for all applications including Open flame fires, which had the tendency to melt the traditional fishing line. The Kit contans all the components and instructions to build 200 WAPIs. These are reusable and virtually indestructable. The cost is $85 (about $.42 each) plus shipping. If you are interested in a fun project that teaches about the perils of unclean water and then show folks how to make a difference, contact us at WAPI@pacbell.net. This is a great fellowship project for Rotary Clubs, Rotary Interact Clubs, Church youth groups, etc.

Cool WAPI

Cool WAPI kit, 1-29-13

The Cool WAPI can be purchased assembled or as this kit. See various types, and purchasing information at the Cool WAPI

A Cool WAPI design does not require heat sealing the tube, but uses a plug to seal the ends instead. See various types, and purchasing information at the Cool WAPI

See Instructions for Assembling the Cool WAPI.

Reports

See also

External links

Around Wikia's network

Random Wiki